How to Replace the Brushes in a Makita Drill

So the time has come to replace the brushes in your Makita drill. Don’t worry, this is a very simple process when you have the right steps. So, I’ll lay down a few preliminary factors and then get straight to the point. You’ll want to read your drill’s manual. There, you will find valuable information regarding your brush replacement (and any other thing you might wonder about in the future). Also, because many drills take different brushes, you’ll want to ensure you have the right brushes for your specific model. And finally, simply make sure the drill is entirely off, unplugged, and otherwise powerless. Anesthetize it, so to speak, and then we’ll cut to the chase.

As we move on to actually finding our brushes, the chase begins. Generally, Makita drills provide easy access to their carbon brushes. Unless your model is of the particularly old variety, you will have either a rear cover or brush caps. A rear cover is a dome-shaped piece of the drill housing at the very rear of the drill that can be removed without completely disassembling the housing. Removing the rear cover should plainly expose the brushes. Brush caps will be on either side of the drill, also near its rear. They are, again, small pieces of the housing (about one square inch in size (give or take) that are usually black in color (or some shade different from the whole of the housing)) that when removed will take you straight to the brushes. If you don’t have brush caps or a rear cover on your drill, you will need to open-up the drill’s housing or clamshell. Keep in mind when removing anything from the tool though, that you will soon have to replace it; reassembly hinges on the organization of disassembly. After removing the top half of the housing, the brushes should be located at the at the back of the motor in the rear of the drill.

The brushes will be tucked into a guide sleeve. Remove them from the guide sleeve and replace the new ones in exactly the same fashion as the others were removed. Your brushes should be making solid contact with the armature and just like that, the chase is essentially complete. Carefully put the drill back together and re-engage it for the final step of the procedure. Test all the functions of the drill; run it in forward and reverse, change the gears if you have the capability, drive a screw or drill a hole and make sure all has come back together properly. If all checks out, then you have successfully replaced your brushes. However, if all things don’t check out, you should retrace your steps to ensure no minor mistakes climb out of the woodwork. Take the drill to a Makita authorized service center if no mistake emerges or if any problems persist.

Small Drill Rigs For Pile Driving

Drill rigs have become a common sight on commercial construction job sites due to their versatility. Because construction sites offer unlimited variations of challenges, manufactures of drill rigs have developed technically advance machines that provide site managers and subcontractors with multiple options to facilitate speedy solutions when time is of the essence.

Unlike projects that are located on wide open spaces, renovation construction project managers must take into consideration a multitude of existing variables. Renovation challenges may include jobsites with limited access, limited overhead space, confined spaces, and the need for businesses (both onsite and adjacent) to be minimally impacted. For these reasons, a variety of options are available for use.

Project manager are sometimes challenged with the need to provide additional foundational support to existing structures. These situations result in the need for creative solutions. In most cases the existing structures pose limitations that can be resolved with traditional drill rigs.

Many manufacturers have addressed this need with low overhead drilling rigs. Some of these rigs require as little as six feet of overhead clearance to drill micropiles. To add to their allure, most of these machines also utilize rubber tracks instead of traditional steel tracks. This allows operators to enter into buildings without damaging the existing slab.

Other features that make these micro drilling rigs desirable are the ability to separate the power source from the drill rig. These attributes prove to be highly valuable, especially in situations where existing businesses wish to remain open while undergoing the construction renovation. By locating the power source in a location that is outside of the building, business owners do not experience the exhaust fumes from the diesel engines that are necessary to power the drill rigs. Placing the diesel engine outside of the structure also greatly reduces the noise that accompanies piling equipment.

Another feature that makes working with micro pile driving drill rigs is the ability of the mast to move separately of the base. Repositioning the entire machine to drill each hole can be extremely difficult in limited access operations. Intelligent design allows an operator to swing the mast from side to side as much as 120 degrees. This permits successful operation in confined spaces.

As renovations become more complex resulting from the desire of building owners to upgrade an existing structure instead of razing it and rebuilding, project managers and construction firms must continue to leverage cutting edge technologies offered by drill rig manufacturers to maintain cost efficiencies. Drill rigs that offer versatility and functionality in small spaces have become the solutions that are most often requested.

International Construction Equipment (ICE) is located in Matthews, NC and has been manufacturing and supplying premiere construction equipment for over 25 years, including a variety of top of the line pile driving equipment; including drill rigs.

Keep Drilling Until You Officially Receive Your IRR Orders

One issue, that many Troop Program Units (TPU) face, is the non-participating soldier. These are soldiers, who are supposed to drill, who aren’t drilling. This list tends to grow until it negatively impacts the unit’s overall readiness and numbers.

While absent, these soldiers’ medical statuses go amber, then red. They end up overdue for the Army Physical Fitness Test (APFT). These soldiers show delinquency on Structured Self-Development (SSD) and other administrative requirements.

Many of these soldiers think that they are in the IRR. More soldiers join their ranks who also think that they’re in the IRR. Their numbers collectively increase and work against the unit. Now, the Commanding Officer, the Command Sergeant Major (CSM), The First Sergeant (1SG), Retention NCO and unit staff feel “fire” on their necks from higher echelons.

What’s being done to address non-participating soldier caused administrative “carpet bombings”?

This has reached the point to where there is a growing push to purge these soldiers. Although the regulations has an IRR transfer as an option, the fate that awaits these soldiers is worse. These soldiers are looking at automatic reductions to E1 and an “Other Than Honorable” (OT H) discharge.

The above medical, educational, and physical fitness statuses do not get updated. Soldiers requiring status updates think that they are in the IRR. Unfortunately, for many of them, they are still TPU.

This is an issue impacting multiple units across the Army Reserve. More importantly, the non-participating soldiers don’t realize that their lack of participation is turning into something negative that will follow them for the rest of their lives.

The biggest issue is misconception surrounding transfers from the TPU to another status.

Many units tell their IRR packet soldiers that they do not have to drill. The packet gets lost, or isn’t processed due to missing documents. The soldier’s TPU requirement is moved from his/her 6 year mark to the end of his/her Military Service Obligation.

Consequently, the soldiers remain on a unit’s book. As their numbers increase, so do the required administrative tasks for the unit. These problems accumulate as more and more soldiers end up in “limbo” as a result of their IRR packets getting lost.

One obvious solution, to avoid this, is to require transferring soldiers to continue drilling until they receive transfer orders.

So, if a soldier is expecting to transfer to the IRR, the soldier should continue to drill after the IRR packet is submitted. This gives the soldier an incentive to continue following up with the UA to ensure that the packet is created and forwarded.

Also, soldiers waiting approval for their IRR packet are still required to attend mass medical events. They’re still responsible to the unit for their own medical, dental, Structured Self Development (SSD), etc. statuses. If a soldier continues to drill, until receipt of their orders, many of those statuses would be updated.

Soldiers should call medical readiness to get their LHI statuses updated.

One of the biggest benefits for the soldier, that continues to drill, is that he/she accumulates drill pay for drills attended. The soldier also receives retirement points for these drills. This means less correspondence courses needed for the current retirement year.

While in the IRR, the soldier is still responsible for achieving a minimum of 50 retirement points each retirement year.

The requirement to drill until orders are received applies to other types of transfers.

If a soldier is submitting a retirement packet, that soldier should continue to drill until his/her retirement orders are posted. The date on the retirement orders will tell the Soldier when his/her retirement is effective.

If a soldier is submitting a packet to transfer to the Individual Mobilization Augmentee (IMA), that soldier is still required to drill. The soldier continues to drill until the date indicated on the IMA orders as the soldier’s being in the IMA.

Transferring to another location?

If you’re on a TPU contract, the requirement for you to drill still exists even after a move. The unit is supposed to send you a letter authorizing you 90 days to find a local unit to drill with. After those 90 days, you’re required to drill.

Ideally, you should be drilling before those 90 days are over. Without this letter, you’ll need to find a unit to drill with immediately.

Soldiers moving to another area of the country need to “drill” with one of the units at their destination. They should do this until orders officially transfer them to the destination unit.

Prepare a DA 1380 to document the drill that you did with the other unit. Submit this DA 1380 to the unit administrator for the unit that you are transferring from. They need this form to process your pay.

If there are no Army Reserve units within the destination area, or within reasonable driving distance, then a transfer to the IRR might be a solution.

Tips:

1. Continue drilling until you receive your IRR orders. This is applicable for other types of transfers from the TPU, like transfer to the retired reserve. You’re still a TPU soldier until the date indicated on those orders.

2. Call the Unit Administrator that’s working on your transfer packet at least once a week. A call where you leave a message isn’t sufficient. You have to talk to this Unit Administrator to see if you need to do anything to complete your packet. After your packet is submitted, use these calls to track your packet’s status.

3. If you get wind that you are moving to another part of the country, speak to the career counselors that service your reserve center. They can talk to their counterparts stationed near the area that you are moving to. This can help expedite your transfer process.

4. As long as you are on a TPU contract, you’re still expected to drill every month and to do some annual training. This is applicable even if you transfer to a new area.

5. If your paycheck shows payments for SGLI, you will accumulate a debt to the government for your SGLI premium for the months that you don’t drill. This will continue to accumulate while you are in a TPU status. Continuing to drill, until your orders come in, helps ensure you don’t have to pay this back in the future.

6. Check your medical readiness status. As of this post, the status is available on AKO.

What Is Diamond Core Drilling & How Is It Useful?

Diamond core drilling has come up as the best method to remove large pieces of cylindrical materials from concrete surfaces. The drill bits used for this purpose are fitted with diamonds that can easily cut most of the materials easily. The term diamond core drilling is derived from the process of drilling or cutting materials using diamonds. However, it is not just used for cutting cylindrical holes from concrete surfaces, it is instead used in multiple other purposes requiring hard-core drilling.

Diamonds with industrial strengths are finely placed into the ends of the diamond core drill bits which are used to drill concrete or rock material easily. The bits possess greater strength and thus lasts longer giving precise drilling solutions. Most of us have heard that drilling and cutting processes are not dusty but also produce lots of noise, although nothing like this happens in the case of diamond drilling.

This process mainly requires light and easily transportable equipment which can be used almost all places which include underwater too. There are multiple varieties of drill bits which are used according to their purpose of usage and the type of material on which they are going to be used on. Hence each drill bit in diamond core drilling process is specifically built and thus can be changed according to the purpose.

5 Top Advantages of Diamond Core Drilling

Here is a list of the top-benefits you can consider prior to picking this services for your project:

1. Drilling procedure is quick, effective, noise and dust free. It can easily dig a hole of 4mm through a brick wall just in 60 seconds, which is simply awesome.

2. Can be subjected to almost all type materials.

3. It is not very difficult to become an expert in diamond core drilling

4. Choose when you need precise and finished cuts to be made

5. Doesn’t require an extended workforce or efforts to operate

The diamond drill bits are majorly used to dug varied type of materials and since the process is so clean requiring less after project clean up, their usage has risen in past few years amongst industries. Diamond drill bits have been effectively used in exploration drills as they are capable of holding a certain amount of materials during mining/drilling.

So, now that you have an idea about what this process is actually about, I hope getting one for yourself won’t be a hassle for you anymore.

The Dewalt DC721 – A Tough Drill and Driver Combination

The up and coming power tools for the construction industry today all seem to have one thing in common; the name “Dewalt” is stamped on them. “Dewalt” has also been burnt into the design of each of these power tools. This shows in their rugged character, the intricacy of their design, and their durability. All this ensures they will last month after month under the toughest working conditions. And isn’t real day in and day out time on the job the ultimate test for a power tool?

The Dewalt DC721 is a fantastic example of what a great company can build if they hold themselves to the toughest standards. The DC721 contains both an impact and drill driver, and there’s a range of on the job uses between these two machines that make it a truly dynamic duo. The DC721 drills through iron and other tough metals. This makes it a good tool for repairing other tools, predrilling for screws or bolts, fastening pipes to joists, and framing.

According to the Dewalt DC721 Review, the DC721 has several speeds that make it easy to control, for those drilling jobs that require a lighter touch, or those jobs that you want to move faster on. The trigger of the drill is ergonomically designed to avoid too much wear on the joints of your fingers and wrists. This drill has gears made completely of metal, so it will last a long time even while drilling tough metals.

The DC827 Impact Driver packs a whopping 1,330 inch-pounds of torque. This gives it the force needed to do the work of fastening. The nickel cadmium power pack gives up 200 watts of power, allowing this potent tool to pound out up to twenty-seven hundred hits each minute. It weighs less than two kilograms, which gives it plenty of mobility to move your work to anywhere on a jobsite.

Despite the durable transmission, the Dewalt DC721 kit is light. This is because light but sturdy, almost unbreakable materials are used in its manufacturing. Its eighteen volt power pack is compact and light, supplying plenty of power but not getting in the way of the task. The DC721 has LED lights, which are becoming more and more popular in power tool kits these days. If you have ever stumbled around in itchy insulation in an attic or crawled across dirty wet plastic underneath a house trying to avoid spiders and snakes, you will appreciate this light.

According to the Dewalt DC721 review, this drill takes a bit up to ten millimeters. Its 350 watts of power is more than enough for the toughest job. At two kilograms, it handles easily but has the durability to take the wear and tear of the job for you. This is an ergonomic advantage, sparing your hands and wrists from injuries that might’ve been caused by too heavy a tool or awkward handling of the tool. The DC721 will drill thirty-eight millimeters into wood and ten millimeters into metal. It is truly a tool to be reckoned with, spreading its usefulness over two tools, and offering state of the art LED illumination to reach even the darkest of work areas.

Seven Of The Most Common Mistakes With Fire Evacuation Drills

Firstly, there is insufficient advance planning for the fire drill. Best practice is to give at least three months notice of a fire evacuation drill to the responsible persons and to follow it up with two low key reminders to ensure business units or tenants are adequately prepared. If the fire drill to be as effective as possible, it is important that only a few key people know about it in advance. It is not unusual to see people, coats on, hot drink in hand, waiting in reception minutes before the evacuation begins, this just wastes everyone’s time.

Secondly, the current fire drill procedures are not reviewed. Are the current fire procedures relevant and up to date? You should consider whether anything has changed, for example evacuation routes, number of employees or risk assessment findings. If necessary, revise and reissue your procedures well in advance of the fire drill. It will also help with the ongoing provision of information to staff and others.

Thirdly, too many people are informed about the planned drill. Liaise with the people who really need to know the fire drill date. Between you, set one date that will minimize the inconvenience for the organisation. Once it has been agreed, the date should only be moved in exceptional circumstances. If the date and time are changed more than twice then it is likely to never to happen.

The fourth mistake is, failure to have Personal Emergency Evacuation Plans (PEEPs) in place. Personal Emergency Evacuation Plans (PEEPs) are essential. These are produced for those people who may require assistance with evacuation such as those with sight or mobility impairments. It is important that the evacuation drill thoroughly challenges the PEEP you have in place and the nominated employees for whom you have to provide safety assistance. To prevent additional pain or discomfort to any person affected, you may ask them to work from home on the day of the fire drill and nominate an able bodied person to stand in for them to test the PEEP. It is important that you should not allow for anyone to remain in the building during the fire drill.

The fifth mistake is, not treating a fire evacuation drill as an audit. When planning or improving your fire drill, the key is to see it as an audit. There need to be objectives, a method, records and reviews. The fire drill is not only a test of the evacuation strategy, but also a test of the effectiveness of those with special responsibilities, such as the fire wardens.

For this reason it is better that as few people as possible are aware of the impending fire drill. A fire warden must be able to carry out their responsibilities whether it is a drill, a false alarm or a real fire.

Not recording the outcome can be the sixth mistake during the fire drill. After the fire drill, you should have observed and recorded the following times:

  • start time
  • each floor or area confirmed as clear
  • successful grounding of all lifts
  • overall completion of the drill
  • minutes and seconds for full evacuation
  • any other observations

The drill should have created no more than 15 to 30 minutes of minor inconvenience. It is a small price to pay to help you avoid become part of the fire statistics.

The final and seventh mistake is, not giving feedback to everyone involved. As soon as possible after the fire drill you should review the performance of the evacuation. This should involve fire wardens, security personnel, tenant representatives and other affected parties. Ensure that comments cover both the positives and the areas for improvement. Where there are improvements identified the necessary action must be taken immediately but it should also be considered in reviewing your procedure when planning your next fire drill.

Publicise the post-evacuation report to everyone involved and keep the findings under regular review. Take the opportunity to thank everyone involved and remind them of the importance of their continued support. If you need help with planning or managing your fire evacuation drills it is available – you just need to ask.

How to Put a Hole in a Glass Bottle

Over the years, I have found my self in situations where I have needed to put a hole in glass bottles or just glass. From craft projects for the kids, fixing up the garage, or helping my friend make soda bottle wind chimes we have settled on our top 3 methods! Here is how to put a hole in a glass bottle! Remember all methods will require some patience, so make sure you have set aside some time to complete your project!

Method 1

By far the Diamond drill works best! YOU can purchase these from several different places, we have found eBay to be the cheapest! Make sure you cover the bottom of the bottle in tape and leave a circular shape open in your desired location. Proceed using your drill on a very low speed! Be patient! You can also pick up some drilling oil to help with all the cutting. *water works too!

Method 2

Using a Round Tapered file and Drill. My husband refers to it as the rat tail file. Anyway, you need to get some turpentine and place some into a small oil can that has one of those squirt tops. You will use this to apply applications in between filing. This is a slow process so make sure you use the slowest setting on your drill. Remember to let the friction of the file do the work, don’t try to rush the process by pushing down firmly.

Method 3

Duct tape and lighter! I have not personally tried this, but my friend swears by it. She makes a lot of glass wind chimes and says this is the only way to go. Its easy and nearly costless! First, cover the bottom of your bottle in duct tape. Remove your desired circle, then make sure you wet the surrounding edges of the tape, along with your fingers. *She suggests to keep a glass of water handy, so if your fingers get hot you can just dip them in the glass. Next, use your lighter and heat up the bottom of the bottle, and once it gets super hot place it directly in cold water. Sometimes your circle will not break out all the way, but you can Finnish off with a file, or a ball peen hammer!

All of the above methods, will take some patience! There is no quick way! I have heard of other methods, but these are the safest for your bottle. Any method containing alcohol or acetone combined with lighting will cause major stress points or fractures in your bottle. I hope that you will find this useful and have some new knowledge of how to put a hole in a glass bottle. Remember slow and steady always wins the race!

What to Look For in a Cordless Drill

I enjoy home improvement work. Not complicated things like building an addition or tearing off a roof, but typical do-it-yourself type projects like remodeling kitchens, fixing up bathrooms, a general maintenance around the house. Over the years, I’ve collected lots of tools: both hand tools and power tools. Some of my favorite tools are my cordless tools. They give me the freedom to move around the house and fix things quickly and easily. And probably the most useful tool of all would be my cordless drill.

My first cordless drill was a Makita 9.6 V model. At the time it was state-of-the-art. With it I could work for sometimes up to an hour without having to change batteries. Back then, we learn to have plenty of spare battery packs since they didn’t last very long. And if I had a big project finish that took several hours I was constantly changing and charging batteries.

My next upgrade was to a Porter cable 12 V drill. Even though it was only 2.4 volts more powerful, it lasted much longer than was much more powerful. This was due to the fact that battery technology has improved greatly in the several years that I owned a Makita. But, like all cordless tools, batteries only last so long. So I was again faced with having several batteries and a couple of chargers to keep this tool running all day long.

My latest drill is an 18 V model. Even though this has 50% more power than my old 12 V model, it doesn’t seem much more powerful and certainly doesn’t seem to last any longer. In fact, I find that I use my 12 V drill more frequently than this newer 18 V one. My old Porter cable is a little bit lighter and seems to be balanced better than the new one. Using them for hours on end, I think that balance and weight are more important that battery life.

So if you are shopping for a new cordless drill, don’t just buy the one with the most volts thinking that it is the best tool for you. You really need to pick them up and see how they feel in your hand. While battery life is important, if the tool is a comfortable to use, you won’t be using it to its fullest potential. I have a toolbox full of old tools but I don’t use because I don’t like the way they feel or they are too tiring to use.

One other feature to look for in a new drill is a small light. I saw this on a newer craftsman drill and it does work quite well. When you’re drilling a hole in the low-light situation, it helps to have some extra light. These tools have a small blue white LED mounted near the front of the tool that shines a light where you are drilling. This doesn’t draw much battery power and really helps with productivity and accuracy.

Wrestling Drills For Balance And Muscle Memory

Keeping in Shape with Wrestling Drills

As with any sport, it’s important for wrestlers to perform a series of wrestling drills to keep them in their finest form on and off the mat. Since wrestling is a sport that requires brute force and agility, the repetition of these drills not only builds strength in the necessary areas, but also helps to build muscle memory which can be essential in winning wrestling matches. Try these wrestling drills during practices or as a part of the pregame warm-up.

Aim for the Knees

First, here’s a drill called “Knee Grab” that’s appropriate for wrestlers of all ages. To begin, two wrestlers of comparable strengths stand facing each other in their regular stances. Both wrestlers should have their hands facing downwards and extended out near their knees.

In this drill, the wrestlers will attempt to use their hands to grab their opponent’s knees while trying to keep their opponent blocked on the outside. Make sure the wrestler really grab for their opponent’s knees as opposed to just a mere tap or slap. Run this drill for 2 or 3 sessions of 20-30 seconds in length, allowing the wrestlers a 10-20 second rest between sessions.

When performed correctly, this drill can be quite physically demanding. Since performing countless wrestling drills can become monotonous, some coaches like to inject a little competitive spirit into their drills. This is one of those drills that functions really well as a mini-competition, with the winner of each pair facing off with a winner of another pair until only one wrestler remains victorious.

Grabber-and-Go

Next is the “Grabber” drill, which is great for building upper-body strength. To begin the drill, two wrestlers stand facing each other in their regular stances. At the sound of the coach’s whistle, both try to get their opponent in a body lock or to get behind their opponent while remaining in an upright, standing position.

The best moves for winning this drill are the duck under, arm drag to body lock, or the wrist lock. Some coaches will allow head locks for this drill as well. Perform this drill for 3 sessions of 30 seconds in length, allowing at least a 10-20 second rest between sessions.

A Fine Balance

This next drill called “Hopper” is a simple yet effective way of helping wrestlers develop and maintain their balance. To begin the drill, two wrestler stand facing each other in their regular stances. At the sound of the coach’s whistle, one wrestler grabs and holds their partner’s foot at waist level. They are permitted to move the foot as much as possible without bringing it above chest level.

The goal of this drill is for the wrestler on one foot to constantly readjust their balance to avoid falling to the mat. Run this drill for 2-3 sessions of no more than 20 seconds, as it is quite tiring for the wrestler on one foot.

Long Drop Drill

The long drop drill is designed to provide proper quarterback drop back technique. This drill should be performed on a straight line that is least 30 yards long. A lined field for any sport would work just fine because there is at least one line that goes all the way across the field.

Start on one side of the field in your proper, athletic quarterback stance holding the ball in front of you as if you are taking the center snap. Keep your chest up and eyes scanning the entire field. This will ensure a proper start to the drill.

Take your first drop back step and turn your shoulders. Bring the ball up to the proper position, hand and elbow up.

Continue the drop back with an open shoulder. Your feet should not cross. Again keep your head up with your eyes scanning the defense.

This drill will train the quarterback to continue proper ball placement, body control and force the quarterback to feel comfortable dropping back while keeping his head up, eyes looking for a receiver.

Continue dropping back approximately 15 yards. This should be long enough to get the feel of proper body positioning. At the end of 15 yards have your quarterback plant his foot and continue through the throwing motion. If you are alone, obviously don’t throw the ball because you will repeat the drill all the way across the field. As you get to the other side of the field, when you plant your foot and throw the ball back to the starting point of the drill.

Repeat the training of this drill often and you will quickly see marked improvement in your drop back.

Freelance Web Designer | WordPress Developer | Hong Kong