Formation Integrity Test (FIT)

Formation Integrity Test (FIT) is the method to test strength of formation and a casing shoe by increasing Bottom Hole Pressure (BHP) to designed pressure. FIT is normally conducted to ensure that formation below the casing show will not be broken while drilling the next section with higher bottom hole pressure. Normally, drilling engineers in town will design how much formation integrity test pressure required and a unit of FIT is normally in pound per gallon unit.

How to Calculate Pressure Required for Formation Integrity Test.

Before forming formation integrity test, you should know pressure required for Formation Integrity Test. The formula showed below demonstrates you how to calculate required FIT pressure.

Pressure required for FIT (psi) = (Required FIT in ppg – Current Mud Weight in ppg) x 0.052 x True Vertical Depth of shoe in feet

Example below demonstrates how to use the formula to calculate pressure required for the test:

Required FIT (ppg) = 14.5

Current mud weight (ppg) = 9.2

True Vertical Depth of shoe (ft) = 4000 TVD

Pressure required for FIT = (14.5-9.2) x 0.052 x 4000 = 1102 psi

Note: The acronyms are listed below;

psi = pound per square inch

ppg = pound per gallon

ft = feet

Formation Integrity Test (FIT) procedures are as follows;

1. Drill out new formation few feet, circulate bottom up and collect formation samples to confirm that new formation is drilled to and then pull a drill string into the casing shoe.

2. Close annular preventer or pipe rams, line up a cement pump, and circulate through an opened choke line to ensure that surface line is fully filled with drilling fluid.

3. Stop the pump and close a choke valve.

4. Gradually pump small amount of drilling fluid into a well with constant pump strokes and recommended pump strokes are 5 to 10 strokes per minute. Record total pump strokes, drill pipe pressure and casing pressure. Pump until casing pressure reaches the pressure required for formation integrity test. Stop pumping and hold pressure for few minutes to confirm pressure stability.

5. Bleed off pressure and open up the well. Then start drilling operation.

Combatives Solo Training Drills

Although training with a partner is the ideal way to train Combatives, quite often we won’t have access to training partners. So rather than not train at all, we can train alone and still get a good session in.

A few pointers to keep in mind when solo training:

  • Don’t try to do too much in one session. Pick just a few techniques or drills to work on throughout the session and stick to them. If you try to cover too much you will scatter your focus and end up learning nothing. Remember that good Combatives training is about repetition. To get good you have to train a select few techniques over and over until you master them. If you try to master too many techniques at one time you will end up mastering none.
  • Train with the street in mind. This means you do not train in a sporting manner. So no shadow boxing or long endurance workouts. Everything you do must be combative, not sporting. Warm up first, then practice your drills and techniques in short bursts. A real street fight is an explosive burst of energy that doesn’t last very long. There are no rounds. Only periods of intense combat lasting only several seconds. Your training must reflect that. So basically, go like fk for no more than ten seconds then stop and repeat.
  • Add emotional content to your training. Whatever you do, you must back it up with the correct mindset. If you hit the bag, do so with full intent and aggression. Really imagine that you are in a situation and you have to put this guy down. Anything less will not do. You are practicing accessing state as much as the physical techniques. Hit the switch, go like fuck and then knock the switch off again, making sure to check state every time. Training in this way, you are making sure the techniques will come out under pressure when you need them. This is the only way to train.
  • Resist the temptation to do long sessions. Long training sessions are for endurance athletes and sport fighters. You will benefit most from shorter sessions of about fifteen to twenty minutes, but train at full intensity during that time. If you feel one session isn’t enough, train twice a day.

1. FENCE AND STRIKE DRILL

What’s good about this drill is that you don’t need any equipment and it can be done anywhere.

Start from a square on stance, then move into a fence position with your arms out front as if controlling your space, then from there throw a pre-emptive strike.

Repeat a number of times.

To make the drill more useful, bring your imagination into play. Pretend there is someone in front of you, giving you grief. Control your space as they try to enter it and then, when you think the moment is right, strike with full intent and see yourself knocking the guy out. Remember, emotional content is what makes these techniques stick.

2. FENCE, STRIKE, BLAST AND FINISH

As above, only after you strike pre-emptively you continue to blast your opponent with multiple strikes, moving forward as you do so (forward drive) before finally finishing your opponent off with knees and elbows or some other technique of your choice.

3. IMAGINARY BRAWL DRILL

For this drill you are going to be playing out a whole attack scenario from start to finish. Think of a scenario first. You could be walking to your car in a dimly lit car park after a particularly tiring day at work or you could be standing outside the chippy on after having had a few drinks with friends. Whatever. Your imagination is the limit here.

Once you have a scenario in mind, really put yourself into it, mentally and emotionally. Begin to act it out the way a real actor would.

Let’s take the car park example. You are walking to your car when you spot two dodgy looking guys loitering near your car. Your spidey sense starts to tingle and you can feel the adrenaline begin to bubble up inside you. Something isn’t right (really feel this!). As you continue to walk to your car, one of the guys (dressed in jeans, black jacket and baseball cap) asks you for a light. You tell him you don’t have one. No sooner have you answered him when the other guy (wearing track suit bottoms and a dark coloured hoodie) suddenly rushes towards you, drawing his fist back in preparation to hit you. The fight is on.

That’s the set up. What way this scenario goes is up to you. The important thing is that you mimic every move as it happens. If you strike one of the guys, then do so for real and really feel the impact. If you get hit or grabbed, react to that for real.

Fall to the floor and grapple. Enact the whole fight. Then when it’s over, walk away.

Done right, with your imagination in full swing, this can end up feeling like a real fight. It’s almost like visualisation practice but you are physically acting out each movement instead of just picturing it in your head.

Try to be alone when doing this drill. If anyone sees you, they will think you’ve lost your mind as you throw yourself around and fight imaginary attackers!

Steps Involved in Oil Drilling

Energy is a small word but has a huge impact on the world. And so do its production and consumption. The oil industry runs on a risky premise which requires the investment of millions in locating oil hubs and further in the drilling process. After locating sites of oil layers, the next step is drilling the surface to make an oil well, and getting oil from it so that it reaches world markets.

Preparation for Oil drilling

After geologists complete their part of searching for the oil reservoirs, the next step is to drill the area and get the oil out. Boundaries are set at the oil site, and scientists come into the picture as they examine the area and carry out environmental studies. Before drilling the land, there are certain issues that need to be settled.

1. The oil company needs to get the agreement and titles before starting to drill the land.

2. Government policies have to be looked after.

3. Legal jurisdiction should be determined for offshore sites.

Once all the settlements are done, the next steps in the process are as under:

1. Clearance of land and leveling is done.

2. Access roads must be built.

3. Water is needed for the drilling process. Hence a water source must be there nearby.

4. In case no natural water body is available at the site, then a water-well can be drilled.

5. Reserve pits must be dug to dispose the rock cuttings and drilled mud.

6. Protection of environment is a must hence the reserve pits must be lined with plastic.

7. In case the site is ecologically sensitive, then the cuttings shall be disposed off-site through trucks.

Deep bores are dug by inserting steel pipes, and holes are created in the earth after the digging area is prepared by workers. This creates different pressure regions. Then cement castings and pipes are inserted in the holes to separate various pressure regions. Then steel pipes are inserted to deepen the holes. Castings are filled according to the geological conditions of the land. Next, a rotator table is inserted into the hole.

In order to extend the digging, the drill is rotated based on a top drive mechanism. The rocks are cut down into pieces using derrick drills. Mud mixture or drill fuel is poured in via drill string. The fluid comprises of chemicals, mud and abrasives. It clears the pieces of rocks by dissolving them. Compressed air can be an alternative for the drilling fluid.

Dental Work and Tinnitus: Here’s What You Need to Know

However, there is only so much that you can do to take proper care of your teeth. Perhaps the most important part is that trip to the dentist that you take every six months.

There is no arguing with the fact that going to the dentist is necessary and we all shoulddo it. Sometimes there is just no other option. Fillings, cleanings, root canals, crowns, and everything in between are all things that only dentists can do for you. Now, let’s take into account that you suffer from an annoying and downright debilitating disease known as tinnitus, and it can make the situation a whole lot more difficult.

There are some things related to dentistry and your mouth that can cause tinnitus symptoms or make existing symptoms worse. We’re not saying that you shouldn’t go to the dentist if you have tinnitus, but there are some things that you need to be aware of. So, in relation to dental work and tinnitus, here’s what you need to know.

Dental Drills and Tinnitus

One of the biggest problems for tinnitus sufferers when it comes to dental work is the drill. Many procedures in dentistry require the drill to be used. There is no way to put in a filling or doing a root canal without the drill. The problem is that the drill creates a loud and high-pitched noise, which is not only annoying, but can do serious damage to your hearing.

The bad part about the drills is that wearing ear protection will not really help. Yes, you can plug your ears all you want, but the fact is that the loud drilling noise does not take its toll through your ear canal; it creates sound and vibrations in your jaw bones which then go all the way up to your ears. Therefore, the damage to your ears is being causedwithin your head, not from the outside.

So, wearing earplugs won’t do you any good here. The best recommendation that we can give is to tell your dentist to drill in short bursts instead of in a prolonged style. This will minimize the damage caused to your cochlea; it’s not perfect, but it is better than the alternative. The drilling doesn’t cause tinnitus, but it can make existing symptoms much worse.

Fillings and Tinnitus

There is also a link between tinnitus and fillings – those ugly things which dentists put in your teeth to get rid of cavities. Here we are talking specifically about amalgam fillings, which are made of silver and mercury. You might think that they are made mostly of silver, but in fact, amalgam fillings contain a lot more mercury than silver.

The obvious problem here is the mercury, something which is shown to cause neurological issues, mercury poisoning, and of course death. A filling or two is usually not a big deal, but if you have more than that in your mouth, it can be a legitimate cause of your worsening tinnitus symptoms. It has been shown that people with multiple mercury fillings in their mouths absorb on average more mercury per day than the World Health Organization deems acceptable.

In other words, these fillings can cause tinnitus or just make existing symptoms worse, which is due to the high level of mercury in your body. We aren’t going to get into the exact science of things, but the bottom line is that mercury-based fillings can have an impact on tinnitus. Your best bet is to ask for composite resin fillings, something which we would recommend regardless of tinnitus.

Jaw Clenching

The technical term given to jaw clenching is bruxism, and it is yet another thing that can cause tinnitus symptoms and cause existing symptoms to increase in severity. The clenching of the jaw can have serious effects on your nerves.

Seeing as everything in your head is connected in one way or another, constantly clenching your jaw can affect the nerves in your ears. This is one of the less serious things, because the causes of clenching usually have pretty simple solutions. At the same time, there are special treatments, such as a simple mouth guard, which can reduce the severity and occurrence of your clenching.

Dentistry and Tinnitus – Other Causes

There are some other dental procedures which can cause or worsen tinnitus symptoms.

• Ultrasonic plaque removal

• Removal of impacted wisdom teeth

• TMJ

• Abscesses in the mouth

Dentists and Tinnitus

Not surprisingly, it is shown that a ridiculously high number of dentists in the word suffer from some kind of hearing loss in conjunction with tinnitus. This is related to the dental drill we just talked about above. High-speed dental drills have been shown to cause or worsen tinnitus symptoms in an overwhelming majority of dentists who use them daily.

One small study showed that dental practitioners suffer from tinnitus more than twice as much as normal medical practitioners. It is estimated that a very high percentage of dentists, anywhere from 30% to 100% do suffer or will suffer from some form of tinnitus later in their careers. It is said that working with a dental drill all day is the equivalent of having your head beside a running gas-powered lawnmower.

The bottom line is that musicians and people who operate heavy machinery are not the only ones who are at risk of developing tinnitus due to their occupation. Therefore, most dental schools now require students to wear ear protection when working with dental drills.

Conclusion

When it comes to dentistry and tinnitus, things are a little tricky. On one hand, dental work can make the problem worse, but on the other hand, dental work is usually a necessary thing.

Stainless Steel Self Drilling (Tek) Screws – Hard Enough?

Stainless Steel Self Drilling (Tek) Screws – what are they?

The ‘Self Drilling Screw for Metal’ or ‘Stainless Steel Tek Screw’ is a screw designed to self-drill into metal. There are several material types available and they each have their strengths and weaknesses.

Why does the grade matter?

Getting the material right for your application is critical. Some Stainless grades have excellent corrosion resistance (304 and 316) but are relatively soft and will not self-drill through much more than thin aluminium. Other grades like 410 are heat treated and have excellent hardness – but anywhere near salt-water (or any sort of coastal atmosphere) and you will see some tea-staining pretty quick!

Some Stainless grades such as Hardtec and Marutex offer the benefits of both (hardness and excellent corrosion resistance) – but are only available in Hex Washer Face Head style. Getting the right material grade and screw type for your application is critical.

Stainless Steel Self Drilling (Tek) Screws – so what is available?

The Stainless Steel Self Drilling Screws are generally available in 4 main material types within the Stainless range, they are:

Bi-Metal Self Drilling Screws – these are not completely Stainless, the Bi-Metal screw generally has a 304 Stainless Steel body with a Carbon Steel tip. Because of the Carbon Steel tip they are very hard and good for drilling but they are not 100% Stainless Steel. They usually have a 500hrs Salt Spray Protective Ruspert Coating on them to increase corrosion resistance somewhat.

410 Stainless Self Drilling Screws – These are completely Stainless. 410 is a Martensitic Stainless and so can be hardened by heat treatment (which Austenitic types 304 and 316 cannot be). For this reason it has excellent drilling properties – however 410 has lower corrosion resistance than grade 304 and should not be used in highly or even moderately corrosive environments or tea-staining will result.

304 and also 316 Stainless Self Drilling Screws – Because the 300 series of Stainless Steels are of an Austenitic crystal structure – hardening by heat treatment like the 410 grade is not possible. These 300 series screws provide excellent corrosion resistance but are really only good for self-drilling through thin aluminium due to the softness of the grade. Also known as A2 (304) and A4 (316) in Europe.

Hardtec/Martuex Stainless – Both ‘Hardtec’ and ‘Marutex’ are propriety grades of Stainless Steel, made specifically for Stainless Self Drilling Screws. They are hardened by heat treatment and so have excellent drilling performance into metals like grade 410 BUT unlike grade 410, these grades have Molybdenum added to them and have corrosion resistant properties in line with the 300 series Stainless grades. Salt Spray tests show corrosion resistance equal or better to that of 304 grade and not far behind 316 Stainless Steel. They are an excellent screw!

Carbon Steel Tek Screws (Self Drilling Screws) are also available in Class 3 and Class 4 (with a galvanised surface) in Australia and New Zealand. These are commonly used in steel roofing. Aluminium versions are sometimes used for Aluminium cladding (to prevent Galvanic Corrosion from dissimilar metals). However Stainless Self-drilling screws provide the greatest corrosion resistance, particularly when the superior Hardtec grade is used.

You Need To Have the Hitachi DH40MRY Rotary Hammer

Hitachi is a well known brand name in the construction industry. This is because, over the years, they have been producing high quality tools that are being used in construction sites all over the world. The tools are durable, long lasting, have great performance and are very reliable. The Hitachi Company knows how to take advantage of current technology while maintaining the functionality of the tools that they produce. The Hitachi DH40MRY rotary hammer is one of the tools from the Hitachi Company. It is well known for its demolition capabilities because of the high power output it has. Let us look more into this tool.

For this drill to produce high quality torque, it has to work with 110v and 950 watts of power. This will make the drill work at maximum ensuring that it carries out its function as best as it possibly can. The Hitachi DH40MRY rotary hammer also comes with lesser vibrations compared to other tools of its kind. This means that the tool is tolerable even when working with heavy loads. When working with this tool along the tri-axial directions, it produces a full load vibration of 9 metres per second.

The impact energy that this drill produces is great for demolition and that is why you will find that it is sometimes called the Hitachi DH40MRY rotary demolition hammer.

This rotary hammer has a double mode of action i.e. rotary hammer drilling and normal hammering. One can choose the mode they want to operate in depending on the kind of work they intend to do. Although these are the 2 modes that come with this tool, there is also a neutral mode where the tool is neither in hammering mode or rotary hammer drilling mode.

The tool can also work at variable speeds, again depending on a user’s requirements. It has a variable locking system which enable for better control of the tool and for a faster rate when chiselling.

The drilling capabilities of the Hitachi DH40MRY rotary hammer vary depending on the material and they type of bit used. For examples, on concrete, with the normal drill bit, the tool can drill up to a depth of 40mm while with a TCT core bit it can drill up to a depth of 105mm.

The motor produces between 240 to 480rpm when used for normal load conditions. The tool weighs 6.8kgs and makes it easily portable.

All in all, it is a great tool to use for your demolition purposes, and is worth for every penny you spend on it.

Water Well Drilling And It’s Many Benefits

Water is an essential resource in order for humans to live. However, many people are still finding it difficult to have a stable water supply, which can make everyday life quite hard.

Most people, especially those who live in remote areas rely on water delivery to sustain their needs for the valuable resource. This is quite difficult should you have a water shortage. At the same time, this is also quite costly as well. If you have a piece of land and would like to have your own water supply, you may want to engage in water well drilling.

Water well drilling can also have many uses around your home. Doing this can bring many advantages to your everyday living. A primary advantage of course is that you can have your very own water supply. No need to rely on a water delivery company and piping that is very costly and not able to cover all of your water needs.

If you drill a well that is deep enough, you will have access to an unlimited water supply all year-round. Also if you are in a more remote area and you are maintaining a farm, water well drilling is a great help for your irrigation needs, ensuring that your crops get as much water as they need, especially during summer.

Having such wells can also be used to supply geothermal power to your home. Not only is this a very cost-effective way of having an auxiliary power source, such means of acquiring energy does not have any negative impact on the environment.

What type of equipment do you need for water well drilling?Aside from time and a lot of effort on your part, it is crucial that you have a reliable water well drilling rig to do the task. Since this kind of project is hard on the equipment, it is important that you get the best possible rig that fits your budget.

Skimping on the quality and reliability of the rig can lead to many problems as your project goes on. The manufacturer of a rig is a good determinant on the reliability and quality of the equipment. Choose a manufacturer that has been into water well drilling for some time, and has received a lot of positive feedback from fellow users.

It is also important that the rig is fairly easy to use, with functions that come with as little hassle as possible. You also need to consider the water well drilling rigs’ mobility. For home projects, it would be best to choose a rig that is smaller and can easily be pulled. This should allow for an easier process of picking a spot to drill for your water well.

Turning A Wooden Mallet

One good thing with the wooden mallet is that, it is simple to make and is suitable for many hammering needs in a home or shop. Due to its simplicity in nature, one can easily craft it as a hobby. When making a wooden mallet, you need to have a number of tools that will make your work easier. To successfully complete mallet project woodturning tools are important; you require parting tool, skew, caliper and a roughing gouge.

When making a mallet, you will require a length wood of about 6″ long by 3 1/4″ square for the mallet head, and another piece with a length of 12″ and width of 1 1/4″ square for the handle. The next step you now need to do to is to mark the center of both ends of these pieces of wood to locate the center. This is easily done by measuring form corner to corner, where the lines cross is the center. Mount the large square to the wood lathe using the located centers to align the piece.

Rotate the mallet head by hand, this is meant to test the blank’s stability and alignment on the wood lathe before you switch on the lathe, and begin turning the mallet. As the wood becomes rounded and balanced you can increase its speed gradually, higher speed will result in a smother cut. With the help of calipers insure that the wood has an even diameter along the length of the piece. Use the parting tool to locate both ends of the mallet head, you should leave a short tendon then remove with a saw

You can now make some decorative patterns close to both ends of the blank, and then release the blank from the wood lathe. Use a saw to cut off the remaining tendons. You now need to precisely drill a hole in the center of the mallet head where the handle will be fitted into. To do this, you can us a drill press to drill the hole for the handle. Make a jig to hold the mallet head to keep the head stable, usually a large “V” notch in another piece of wood will suffice to hold the round head. Drill a vertical hole for the handle in the center, both end to end and side to side.

The next step is to make the mallet handle. Mount the small square wood into the wood lathe, the procedure is the same as for the mallet head. Use the roughing gouge, round the blank and shape the handle to your personal design. Ensure that the handle diameter meets your requirements; fits your hand. Create a short tendon to match the diameter of the hole you drilled into the mallet head. The tendon should have a slight taper, from smaller than the drilled hole to larger than the drilled hole, this will insure a tight fit. Again remove the tendons with a saw.

Both the Mallet head and Handle have been sanded and the tendons removed you can how glue the two pieces together. After the glue is dry apply a coat of oil to preserve the mallet. Mineral Oil, Linseed Oil, Tung Oil, or what ever you would like, I shy away form varnish as it tends to be slick and makes a good grip difficult.

Makita BHP451 Review – Read My Detailed Look at One of Makita’s Finest Hammer Drills

If you’re in the market for a new hammer drill/driver, you may want to take a look at the 18-V Makita BHP451. This particular Makita has a ton of features that you don’t find with other hammer drills and it’s sure to assist you with finishing almost any tough job you ask it to.

The Makita BHP451 comes with a new technology of batteries known as the LXT Lithium-Ion system and it offers a ton of advantages over the standard NiCad or NiMH batteries that are found in a lot of drills.

Not only are you getting around 1,400 battery life cycles with this new technology, but the run time is much longer, it charges much quicker, and the batteries are lighter in weight. This means less worry about your arm getting worn out during heavy drilling. These Li-Ion batteries also come with built-in shock absorbing features to help protect them and the drill.

Another really cool feature about the Makita BHP451 is the new 45-minute Optimum Charger. It uses a built-in memory chip in the battery and a CPU chip in the charger to communicate with one another. The purpose is so that the charger can analyze the data in the battery and determine the best charging method at the time.

Even though the Makita BHP451 is a high powered drill that packs 560 in./lbs. of torque, it’s still fairly compact and lightweight. At only 9-7/8 inches long and 4.9 pounds, you can drill for extended periods of time without getting tired.

There are 3 speed settings you can choose from as well: 0-300 RPM on low, 0-600 at the mid level, and 0-1,700 RPM in high gear. This ensures you can always choose the perfect speed for whatever project you’re working on.

In hammer mode, this drill delivers up to 4,500 blows per minute (BPM) on the lowest gear, up to 9,000 in the middle gear, and an astonishing 25,500 BPM at the third and highest gear! It’s also extremely easy to switch from drill to drive mode with the new Shift-Lock drive system.

Yet another great feature of the Makita BHP451 is the LED light. If you work in smaller or dark spaces often, you will really enjoy this addition.

The Makita BHP451 has an exceptional amount of power, is lightweight and comfortable to hold, has a really great battery system, and tons of other cool features. All around, I think this is an awesome hammer drill/driver and it’s worth checking out for yourself.

Two Power Coil Golf Swing Drills to Fire-Up Your Golf Swing

Golf swing drills are designed to imprint memory on your muscles on how the swing feels. At the same time, golf swing drills also let your muscles know how the wrong golf swing feels. This is all done by decelerating the golf swing to heighten your awareness of your body’s every movement from the backswing, to the downswing, impact, and follow-through.

What powers an excellent golf swing that produces both distance and accuracy? The graceful tightening coil of your body as you do the backswing, and the fast-snap and fluid uncoiling of your body as you do the down swing, hit the ball and continue to a full follow-through, all bring power to your golf swing.

Below are two of the most effective golf drills for developing a powerful body coil that will fire up your swing.

1. Golf Swing Drill for More Power-Producing Body Coil

The First drill is to know how it feels for your body to be coiled at the optimum level during a backswing. This simple golf drill will be one of the most useful drills you will learn for improving your swing.

So start by swinging your golf club until you are at the peak of your back swing. At this point, the golf club should be high in the air for a full stretch, your left shoulder dipped a little to accommodate this stretch, and your left knee also bent slightly. You should be able to feel the energy gathering in your body as it wounds into a tighter coil.

Next, perform the down swing. Pause the swing just before it hits the ball. Feel how your body uncoils naturally in the down swing, how your left leg straightens and your body weight shifts to the left foot (reverse if left-handed).

After repeating the backswing and downswing coil several times, now hit the ball and completely follow-through. Be mindful of how your body coils smoothly and increasingly to the right during the backswing, and how it uncoils at a faster speed to the left during the downswing. Also be mindful of how your golf club squarely hits the ball and flies all the way up to follow-through.

2. Golf Swing Drill for Better Arm Rotation

The more effective golf swings are done on a single plane. This next golf drill will help you accomplish this by improving your arm rotation.

So without any golf club, get into a golf stance at address. Your weight should be balanced equally on both feet. Next, let your arms fall down naturally and then bring your hands together palm-to-palm.

Then rotate your hip and arms to do a backswing while trying to keep your palms still in-contact with one another. To be able to retain this palm-to-palm contact, you need to hold your arms close together during the rotation, while continuing to keep your left arm straight. In this position you can only do a half-backswing.

This drill is important because it trains your arms to rotate into a backswing position properly, which is having your left arm in a straight position (for right-handed folks) and keeping both of your arms in close proximity to one another during the backswing.

So practice these golf drills to get your body in tune with the movements of a perfect golf swing. Make your mind focus on each move to build better motor memory. It won’t be long before you will see improvements in your golf score.

Freelance Web Designer | WordPress Developer | Hong Kong